三端保险丝 30A62V 5.4×3.2 5串
1.适用范围Scope
本规范适用于苏州鼎时电子有限公司生产的自控制保护器。
This Specification applies to the fuse linked with heater which made by LANSON ELECTRONICS Corporation.
2.适用安全标准Applicable Safety Standards
UL248-1，Ul248-14。
3.UL认证 UL File Number
E221465.
4.外形与回路图 Dimensions and Circuit Chart
4.1外形图 Dimensions
（4）产品的尺寸代码，J表示4.0mm×3.0mm×0.85mm，H表示5.4mm×3.2mm×1.35mm，K表示9.5mm×5.0mm×2.0mm等。
Dimension code of the product, J means 4.0mm × 3.0mm × 0.85mm, H means 5.4mm × 3.2mm × 1.35mm, K means 9.5mm × 5.0mm × 2.0mm, etc.
5.规格 Rating
|
型号 Part number |
额定电流Current Rating |
额定电压★ Voltage Rating |
最大阻断电流Max. Breaking capacity |
保险丝电阻Fuse DCR |
适用电芯数Cells in series |
动作电压范围Operating Voltage |
|
A |
VDC |
A |
m Ω |
cell |
V |
|
|
SCP30A5H |
30 |
62 |
80 |
0.5-2.5 |
5 |
17.10~23.50 |
★额定电压是保险丝组件可以安全阻断的最大电压值，不是发热器组件的动作电压。
★Rated voltage is the maximum voltage that the fuse can block, not the action voltage of the heater assembly.
6.环境性能 Environmental Characteristics
（1）产品中使用的各种材料的卤素含量如下表所示。
Contents of halogens used in each material for the product are as follows.
|
卤素 Halogen substance |
含有量 Content |
|
氯（CL） Chlorine（CL） |
≤ 900ppm (0.09%) |
|
溴（Br） Bromine（Br） |
≤ 900ppm (0.09%) |
|
总和（氯(CL)＋溴(Br)） Total concentration of chlorine (CL) + bromine (Br) |
≤ 1500ppm (0.15%) |
（2）本规范中描述的产品符合ROHS指令。BOM表中的合金、焊料、一些电子浆料含有铅，但都符合ROHS指令的高铅豁免相关规定。。
The product described in this specification complies with the ROHS Directive. BOM table contains the alloy, solder, some electronic slurry, including lead, but these are exempted from ROHS requirements.
7.性能Characteristics
7.1．测试一般条件 General Conditions of Measurement
除非特别指定，否则按以下环境条件进行测量。
In the absence of additional test environmental standards, the test environmental standards are as follows;
环境温度：5～35℃；
相对湿度：45～85%RH；
气压：86～106KPa。
Ambient temperature: 5 to 35℃.
Relative humidity: 45 to 85%RH.
Air pressure:86 to 106kPa.
如果在判定产生疑义的情况下，按照以下条件进行测定。
If you have any questions about the test results, please follow the following environmental standards.
环境温度：20±2℃；
相对湿度：60～70%RH；
气压：86～106KPa。
Ambient temperature: 20±2℃.
Relative humidity: 60 to 70%RH.
Air pressure: 86 to 106kPa
7.2．电气的性能 Electrical Characteristics
|
No. |
項目 Items |
測定条件 Conditions |
技术规格 Specifications |
|
1 |
熔断时间 Clearing time |
产品参照《电压动作特性测试方法》连线，向测试板（4-1端或者4-3端）施加对应规格的动作电压 Apply the operating voltage to the heater. For other procedures, refer to《Voltage action characteristic test method》. |
保险丝组件一分钟内熔断。 The fuse shall be melt Within 1min.
|
|
产品参照《电流动作特性测试方法》连线，向测试板（1-3端）施加两倍额定电流。 Energize both ends of the fuse with twice the rated current. For other procedures, refer to《Current action characteristic test method》. |
|||
|
2 |
通电容量 Current carrying capacity |
产品参照《温升测定方法》连线，向保险丝组件（1-3端）施加额定电流。 Energize the rated current at both ends of the fuse. For other procedures, refer to《Temperature Rise characteristic test method》. |
保险丝组件1小时内没有熔断。 No melting within 1 hour |
注：
电气性能受基板热容量、零件、图案宽度等条件的影响。因此，请将产品安装在客户实际使用的基板上确认特性。
Electrical Characteristics is influenced by thermal capacity of PCB, parts, pattern width, and so on. Therefore you should check it on your PCB.
7.4．耐久性能 Endurance Characteristics
|
NO |
項目 Items |
測定条件 Conditions |
規格 Specifications |
|
1 |
高温 Dry heat |
在100±5℃环境保持6小时后，常温常湿条件下放置1小时后进行测量。 The fuse shall be stored at a temperature of 100 ± 5 ℃ for 6h. And then it shall be subjected to standard atmospheric conditions for 1h, after which its measurement shall be made. |
没有外形变形，上盖脱落等异常，满足电气性能。 Without deformation of case or excessive looseness of caps. Electrical characteristics shall be satisfied. |
|
2 |
低温 Cold |
在-20±3℃环境保持500小时后，常温常湿条件下放置1小时后进行测量。 The fuse shall be stored at a temperature of -20±3℃ for 500h. And then it shall be subjected to standard atmospheric conditions for 1h, after which its measurement shall be made.
|
|
|
3 |
湿热 Damp heat |
在40±2℃、相対湿度90～95％RH环境保持250小时后，常温常湿条件下放置1小时后进行测量。 The fuse shall be stored at a temperature of 40±2℃with relative humidity of 90 to 95%RH for 250h. And then it shall be subjected to standard atmospheric conditions for 1h, after which its measurement shall be made. |
|
|
4 |
耐久测试 Endurance test |
给产品通电100A电流5ms，断开995ms为一个周期，一起循环一万个周期。 100A be carried for a period of 5ms. The current is there switched off for a period of 995ms.this cycle is repeated 10,000 times. |
外形无明显变形、破损，保险丝组件没有熔断。 Without damage such as deformation or disconnection of fuse element. |
